Login | Register
Home > News Center > technical consulting

What are the common problems and solutions in the use of duct mechanical equipment?
2024-04-25 15:06:19

There are many common problems and solutions in the use of duct mechanical equipment. Here are some common problems and their solutions to help users better understand and solve these problems.

1. Noise problem

Noise is one of the most common problems in the use of duct mechanical equipment. The following methods can be used to reduce noise:

- Check whether the equipment is installed on a stable foundation. If the equipment is loose or vibrating, it should be adjusted or fixed.

- Check if the equipment is installed close to a noise sensitive area, if so, consider moving it to a farther location.

- Check whether the equipment has loose parts or mechanical failures. If so, repair or replace them in time.

- Add soundproofing materials, such as soundproofing covers or soundproofing blankets, to reduce noise transmission.

- Clean the equipment regularly to ensure the air duct is unobstructed and reduce noise. If corrosion or dust accumulation occurs, clean or replace it in time.

2. Insufficient air flow

When the air flow of duct mechanical equipment is insufficient, the following measures can be taken to solve the problem:

- Check the air duct system for blockages or gaps. If any, clean or repair them promptly.

- Check whether the fan is operating normally. If any fault is found, repair or replace it in time.

- Check the fan impeller for blockage or damage, if so, clean or replace.

- Check whether the voltage and current of the fan motor are normal. If abnormal, the motor should be adjusted or replaced.

- Adjust the fan speed or impeller angle to increase air flow.



3. Temperature control issues

When the temperature control of the duct mechanical equipment is inaccurate, the following methods can be used to solve it:

- Check the temperature sensor for accuracy, if inaccurate, calibrate or replace.

- Check whether the temperature controller is set correctly, such as set temperature, control range and other parameters.

- Check the fan operating status and speed to ensure that the fan is providing adequate cooling or heating.

- Check whether the air flow is smooth. If there is any blockage or leakage, it should be dealt with promptly.

- Clean the equipment regularly to ensure the surface of the heat exchanger or cooling plate is clean to improve the heat exchange effect.

4. Excessive energy consumption

When the energy consumption of duct mechanical equipment is too high, the following measures can be taken to solve it:

- Check if the equipment is operating in good working condition, such as whether there is unnecessary load or resistance.

- Check if there are any leaks in the equipment, such as leaks in the air duct, fan or exhaust vent, and deal with them promptly.

- Clean the equipment regularly to reduce friction and wind resistance.

- Check the operating hours and cycles of the equipment and adjust the time or shut down unnecessary equipment if necessary.

- Optimize the operation strategy of the equipment, such as reasonably adjusting the speed of the fan to reduce energy consumption.

In summary, common problems in the use of duct mechanical equipment include noise, insufficient air flow, inaccurate temperature control, and excessive energy consumption. Solutions to these problems include adjusting the equipment installation location, cleaning the equipment, repairing or replacing faulty parts, adding sound insulation materials, calibrating sensors, etc. By operating and maintaining the equipment properly, the efficiency and reliability of duct mechanical equipment can be improved and the service life of the equipment can be extended.


Comment

(0)
*Captcha:

Shanghai Panwei Precision Machinery Co., Ltd. was established in 2005 and is located in Shanghai. The company mainly designs and manufactures small shearing, folding and rolling sheet metal processing equipment; special, dedicated and customized metal processingMolding machinery; Automation instruments, electrical complete sets and CNC intelligent equipment; and provide cost-effective complete solutions. Through independent research and development and continuous improvement, we promote the upgrading of automation CNC technology and form a product series with its own characteristics and outstanding advantages; the products are sold well all over the country and exported to dozens of countries and regions in Europe, America, Asia and Africa.

Reliable quality, supreme service, reasonable price and timely delivery are our commitments to our customers. Panwei Precision Machinery will make unremitting efforts to meet the needs of customers and create value for you with high-quality products and services.


Contact information

Contact: Mr. Xu

Tel: 021-57842497

Mobile: +86 13917353933

Address: No. 5, Lane 188, Yonghang Road, Songjiang District, Shanghai